
Availability: In Stock
The Rearden FHD flash hider in 1/2-28 thread pitch with nitride finish is a precision muzzle device built for shooters running suppressor-ready AR platforms. This flash hider is engineered to work with Plan B type suppressor mounts and Rearden's Atlas and Atlas XL adapters, making it a solid choice if you're building a modular suppressed rifle setup. The black nitride finish offers robust corrosion resistance and a tighter seal when properly installed—key factors in suppressor performance and durability downrange.
The nitride treatment gives the FHD a surface hardness of 67 HRC, lending real durability to a component that endures repeated mounting cycles and suppressor changes. The updated design features larger wrench flats on the rear, making installation and timing easier compared to older generations. The muzzle device is constructed from 17-4 PH H900 stainless steel, a material choice that balances strength with corrosion resistance in demanding field conditions.
Proper installation is essential with any precision muzzle device. You'll need to use an alignment rod during setup, torque the device to the barrel at approximately 30 ft lbs, and lock it in place with Rockset or similar threadlocker. The nitride finish's seal quality depends entirely on clean threads, clean tapers, and correct torque; skipping these steps defeats the benefits of the material. Keep in mind that shims are not included—your barrel may need one if the manufacturer didn't machine a thread relief into the shoulder.
If you're planning to run this with a suppressor, note that pairing this muzzle device with certain cans may affect warranty coverage. Always verify compatibility with your specific suppressor before committing to a setup.
| Thread Pitch | 1/2-28 |
| Material | 17-4 PH H900 stainless steel |
| Finish | Black nitride (67 HRC surface hardness) |
| Mount Type | Plan B compatible |
| Compatible Adapters | Rearden Atlas, Atlas XL |
| Shims Included | No |
| Recommended Torque (to barrel) | Approximately 30 ft lbs |
The Rearden FHD is compatible with Plan B type suppressor mounts and works with Rearden's Atlas and Atlas XL adapters. Always verify that your specific suppressor and mounting system are compatible before purchase.
Shims are not included with the FHD. Depending on your barrel, you may need shims to properly time the flash hider. Check whether your barrel manufacturer included a thread relief on the shoulder; if not, you'll likely need shims to ensure the device seats correctly.
Use an alignment rod during installation to ensure correct setup. Torque the flash hider to approximately 30 ft lbs, then secure it with Rockset or a similar threadlocker. Make sure all thread and taper surfaces are clean before assembly. The flash hider must be square against the barrel shoulder for proper function.
The FHD is designed for suppressor-ready builds with Plan B mounts. However, some suppressor systems may have warranty implications when paired with this muzzle device. Check with both the device and suppressor manufacturers to confirm compatibility before committing to the combination.
SKU: 152744873 • Width: 4in • Height: 1.25in • Depth: 6in






Availability: In Stock
The Rearden FHD flash hider in 1/2-28 thread pitch with nitride finish is a precision muzzle device built for shooters running suppressor-ready AR platforms. This flash hider is engineered to work with Plan B type suppressor mounts and Rearden's Atlas and Atlas XL adapters, making it a solid choice if you're building a modular suppressed rifle setup. The black nitride finish offers robust corrosion resistance and a tighter seal when properly installed—key factors in suppressor performance and durability downrange.
The nitride treatment gives the FHD a surface hardness of 67 HRC, lending real durability to a component that endures repeated mounting cycles and suppressor changes. The updated design features larger wrench flats on the rear, making installation and timing easier compared to older generations. The muzzle device is constructed from 17-4 PH H900 stainless steel, a material choice that balances strength with corrosion resistance in demanding field conditions.
Proper installation is essential with any precision muzzle device. You'll need to use an alignment rod during setup, torque the device to the barrel at approximately 30 ft lbs, and lock it in place with Rockset or similar threadlocker. The nitride finish's seal quality depends entirely on clean threads, clean tapers, and correct torque; skipping these steps defeats the benefits of the material. Keep in mind that shims are not included—your barrel may need one if the manufacturer didn't machine a thread relief into the shoulder.
If you're planning to run this with a suppressor, note that pairing this muzzle device with certain cans may affect warranty coverage. Always verify compatibility with your specific suppressor before committing to a setup.
| Thread Pitch | 1/2-28 |
| Material | 17-4 PH H900 stainless steel |
| Finish | Black nitride (67 HRC surface hardness) |
| Mount Type | Plan B compatible |
| Compatible Adapters | Rearden Atlas, Atlas XL |
| Shims Included | No |
| Recommended Torque (to barrel) | Approximately 30 ft lbs |
The Rearden FHD is compatible with Plan B type suppressor mounts and works with Rearden's Atlas and Atlas XL adapters. Always verify that your specific suppressor and mounting system are compatible before purchase.
Shims are not included with the FHD. Depending on your barrel, you may need shims to properly time the flash hider. Check whether your barrel manufacturer included a thread relief on the shoulder; if not, you'll likely need shims to ensure the device seats correctly.
Use an alignment rod during installation to ensure correct setup. Torque the flash hider to approximately 30 ft lbs, then secure it with Rockset or a similar threadlocker. Make sure all thread and taper surfaces are clean before assembly. The flash hider must be square against the barrel shoulder for proper function.
The FHD is designed for suppressor-ready builds with Plan B mounts. However, some suppressor systems may have warranty implications when paired with this muzzle device. Check with both the device and suppressor manufacturers to confirm compatibility before committing to the combination.
SKU: 152744873 • Width: 4in • Height: 1.25in • Depth: 6in
