$412.45
Availability: In Stock
The RCBS Turret Press Turret is a 6-station interchangeable turret head that transforms your reloading workflow by letting you preset dies for different calibers and swap setups in seconds. Instead of breaking down and reconfiguring your press every time you switch cartridges, you leave your dies indexed and threaded into the turret, then remove the entire head with a single bolt and install a pre-staged alternative. For handloaders who work multiple calibers regularly, this efficiency gain is genuine: you're back to pressing rounds in the time it takes to unbolt and rebolt.
The turret accepts standard 7/8-inch-14 threaded dies, so it works with your existing reloading die inventory. The head itself is built from rugged cast iron and mounts to RCBS single-stage and turret press frames. Each turret accommodates six dies per station, and the press can run in single-stage mode (one stroke per round) or progressive mode, where you'll process between 50 and 200 rounds per hour depending on caliber and operator rhythm. The spent primer catcher is built in, and the priming station accepts both large and small primer sleeves and plugs, supplied.
Setup is flexible: the turret pin assembly and ball handle can be positioned for right- or left-hand operation, and the 4¾-inch operating window gives you reasonable clearance for most rifle and handgun brass. It's a straightforward, American-made tool that pays for itself in time saved if you're serious about reloading multiple cartridges. Note that dies are not included—you'll use your existing RCBS or compatible dies in the turret stations.
| Turret Stations | 6 |
| Die Thread Standard | 7/8"-14 |
| Operating Window | 4¾ inches |
| Press Modes | Single-stage or progressive |
| Progressive Mode Output | 50–200 rounds per hour |
| Frame Material | Cast iron |
| Country of Origin | Made in USA |
The turret accepts any dies with standard 7/8-inch-14 threads. You can use RCBS dies or any compatible brand.
No, dies are not included. You'll supply your own reloading dies threaded into the stations.
Yes. The turret pin assembly and ball handle can be repositioned to suit right- or left-hand users.
In progressive mode, you can load between 50 and 200 rounds per hour, depending on caliber and your operating pace.
SKU: 115687840 • Weight: 2.2oz
Availability: In Stock
The RCBS Turret Press Turret is a 6-station interchangeable turret head that transforms your reloading workflow by letting you preset dies for different calibers and swap setups in seconds. Instead of breaking down and reconfiguring your press every time you switch cartridges, you leave your dies indexed and threaded into the turret, then remove the entire head with a single bolt and install a pre-staged alternative. For handloaders who work multiple calibers regularly, this efficiency gain is genuine: you're back to pressing rounds in the time it takes to unbolt and rebolt.
The turret accepts standard 7/8-inch-14 threaded dies, so it works with your existing reloading die inventory. The head itself is built from rugged cast iron and mounts to RCBS single-stage and turret press frames. Each turret accommodates six dies per station, and the press can run in single-stage mode (one stroke per round) or progressive mode, where you'll process between 50 and 200 rounds per hour depending on caliber and operator rhythm. The spent primer catcher is built in, and the priming station accepts both large and small primer sleeves and plugs, supplied.
Setup is flexible: the turret pin assembly and ball handle can be positioned for right- or left-hand operation, and the 4¾-inch operating window gives you reasonable clearance for most rifle and handgun brass. It's a straightforward, American-made tool that pays for itself in time saved if you're serious about reloading multiple cartridges. Note that dies are not included—you'll use your existing RCBS or compatible dies in the turret stations.
| Turret Stations | 6 |
| Die Thread Standard | 7/8"-14 |
| Operating Window | 4¾ inches |
| Press Modes | Single-stage or progressive |
| Progressive Mode Output | 50–200 rounds per hour |
| Frame Material | Cast iron |
| Country of Origin | Made in USA |
The turret accepts any dies with standard 7/8-inch-14 threads. You can use RCBS dies or any compatible brand.
No, dies are not included. You'll supply your own reloading dies threaded into the stations.
Yes. The turret pin assembly and ball handle can be repositioned to suit right- or left-hand users.
In progressive mode, you can load between 50 and 200 rounds per hour, depending on caliber and your operating pace.
SKU: 115687840 • Weight: 2.2oz