$185.15
Loading...
Loading...
Loading...
Availability: In Stock
The RCBS 1-1/2 Inch-12 Bullet Puller Collet for .50 BMG is a specialized reloading accessory designed to quickly disassemble loaded ammunition and recover your bullets and components. If you're working with .50 BMG rounds and need to salvage brass, primers, and powder from completed loads—whether you're sorting through test loads, correcting mistakes, or recovering components from older ammunition—this collet gives you a fast, reliable way to separate bullets without damaging them.
This collet works specifically with RCBS's big-bore presses: the AmmoMaster-2 or AmmoMaster .50 BMG. The 1-1/2 inch–12 thread pattern is sized to handle the large bullets associated with .50 BMG ammunition. Because .50 BMG is a specialty cartridge with a smaller reloader base than typical rifle rounds, having the right collet for your press setup is essential—generic pullers won't fit or work properly.
Component salvage becomes important when you're reloading expensive rounds like .50 BMG. This collet makes the job straightforward: secure it in your press, insert the loaded round, and extract the bullet without marring it. Clean extraction means you can reload those bullets again or set them aside for future loads, putting the savings back into your shooting.
| Thread Size | 1-1/2 Inch–12 |
| Compatible Cartridge | .50 BMG |
| Compatible Presses | RCBS AmmoMaster-2, RCBS AmmoMaster .50 BMG |
| Function | Bullet puller collet |
This collet is designed for use with the RCBS AmmoMaster-2 or RCBS AmmoMaster .50 BMG press. It will not function with other press models or incompatible thread patterns.
No. This collet is sized specifically for .50 BMG ammunition. Using it with other cartridges will not work properly.
You'll need this collet and the compatible RCBS press. Once inserted into your press's die station, the collet grips the bullet and allows you to extract it from the loaded round.
SKU: 167522181 • Width: 1.95in • Height: 0.95in • Depth: 2.85in • Weight: 0.1688oz
Availability: In Stock
The RCBS 1-1/2 Inch-12 Bullet Puller Collet for .50 BMG is a specialized reloading accessory designed to quickly disassemble loaded ammunition and recover your bullets and components. If you're working with .50 BMG rounds and need to salvage brass, primers, and powder from completed loads—whether you're sorting through test loads, correcting mistakes, or recovering components from older ammunition—this collet gives you a fast, reliable way to separate bullets without damaging them.
This collet works specifically with RCBS's big-bore presses: the AmmoMaster-2 or AmmoMaster .50 BMG. The 1-1/2 inch–12 thread pattern is sized to handle the large bullets associated with .50 BMG ammunition. Because .50 BMG is a specialty cartridge with a smaller reloader base than typical rifle rounds, having the right collet for your press setup is essential—generic pullers won't fit or work properly.
Component salvage becomes important when you're reloading expensive rounds like .50 BMG. This collet makes the job straightforward: secure it in your press, insert the loaded round, and extract the bullet without marring it. Clean extraction means you can reload those bullets again or set them aside for future loads, putting the savings back into your shooting.
| Thread Size | 1-1/2 Inch–12 |
| Compatible Cartridge | .50 BMG |
| Compatible Presses | RCBS AmmoMaster-2, RCBS AmmoMaster .50 BMG |
| Function | Bullet puller collet |
This collet is designed for use with the RCBS AmmoMaster-2 or RCBS AmmoMaster .50 BMG press. It will not function with other press models or incompatible thread patterns.
No. This collet is sized specifically for .50 BMG ammunition. Using it with other cartridges will not work properly.
You'll need this collet and the compatible RCBS press. Once inserted into your press's die station, the collet grips the bullet and allows you to extract it from the loaded round.
SKU: 167522181 • Width: 1.95in • Height: 0.95in • Depth: 2.85in • Weight: 0.1688oz