$80.99
Availability: In Stock
The EGW Mosin Nagant 91/30 one-piece Picatinny base is built for shooters who want to mount modern optics on a classic rifle without permanent modification. This 0 MOA steel base uses the rifle's existing rear sight housing and retaining pin, so there's no unsoldering, welding, or irreversible gunsmithing required—remove the leaf sight, install the mount, and you're ready to ring in a scope. It's a clean approach that keeps your Mosin's original character intact while opening it up to modern glass.
EGW machines these mounts in-house and finishes them with tumbling, sand blasting, and Type III hard anodize for durability that holds up to field use. The full-length Picatinny rail gives you flexibility in ring placement and accessory mounting, and the center channel keeps overall weight down. In many setups, the design won't block your use of factory iron sights, so you can keep backup aiming solutions in play.
Installation is straightforward: the tabbed steel base slides into the rear sight housing, the original pin secures it, and then the aluminum top rail bolts down. You may need to file the corners and front edge slightly for a perfect fit depending on your specific rifle's tolerances—EGW recommends measuring your receiver hole spacing against their published dimensions before ordering. Apply 20 inch-pounds of torque and a drop of blue Loctite (sold separately) to the fasteners and you're done.
| Manufacturer | EGW (E. German Weapon) |
| Rifle Compatibility | Mosin Nagant 91/30 |
| Mount Type | One-piece base |
| Rail Standard | Picatinny |
| MOA | 0 |
| Material | Steel base, aluminum top rail |
| Finish | Type III hard anodize |
| Recommended Torque | 20 inch-pounds |
Yes, this mount is designed for the Mosin Nagant 91/30. EGW recommends measuring the hole spacing in your receiver to confirm it matches their published dimensions before purchasing, as vintage rifles can have minor variations.
No. The mount uses your rifle's existing rear sight housing and original retaining pin, so installation requires no unsoldering, welding, or permanent alterations. You simply remove the leaf sight and install the base in its place.
In many cases yes, because the mount's center channel and design won't obstruct factory iron sight use. However, this depends on your specific rifle and the height of your mounted optic, so check fit before taking it afield.
You'll need a torque wrench (set to 20 inch-pounds), a small brush or applicator for blue Loctite (sold separately), and possibly a small file to carefully trim the mount's corners and front edge for fitment on your particular rifle.
SKU: 194196361 • Weight: 0.2oz
Availability: In Stock
The EGW Mosin Nagant 91/30 one-piece Picatinny base is built for shooters who want to mount modern optics on a classic rifle without permanent modification. This 0 MOA steel base uses the rifle's existing rear sight housing and retaining pin, so there's no unsoldering, welding, or irreversible gunsmithing required—remove the leaf sight, install the mount, and you're ready to ring in a scope. It's a clean approach that keeps your Mosin's original character intact while opening it up to modern glass.
EGW machines these mounts in-house and finishes them with tumbling, sand blasting, and Type III hard anodize for durability that holds up to field use. The full-length Picatinny rail gives you flexibility in ring placement and accessory mounting, and the center channel keeps overall weight down. In many setups, the design won't block your use of factory iron sights, so you can keep backup aiming solutions in play.
Installation is straightforward: the tabbed steel base slides into the rear sight housing, the original pin secures it, and then the aluminum top rail bolts down. You may need to file the corners and front edge slightly for a perfect fit depending on your specific rifle's tolerances—EGW recommends measuring your receiver hole spacing against their published dimensions before ordering. Apply 20 inch-pounds of torque and a drop of blue Loctite (sold separately) to the fasteners and you're done.
| Manufacturer | EGW (E. German Weapon) |
| Rifle Compatibility | Mosin Nagant 91/30 |
| Mount Type | One-piece base |
| Rail Standard | Picatinny |
| MOA | 0 |
| Material | Steel base, aluminum top rail |
| Finish | Type III hard anodize |
| Recommended Torque | 20 inch-pounds |
Yes, this mount is designed for the Mosin Nagant 91/30. EGW recommends measuring the hole spacing in your receiver to confirm it matches their published dimensions before purchasing, as vintage rifles can have minor variations.
No. The mount uses your rifle's existing rear sight housing and original retaining pin, so installation requires no unsoldering, welding, or permanent alterations. You simply remove the leaf sight and install the base in its place.
In many cases yes, because the mount's center channel and design won't obstruct factory iron sight use. However, this depends on your specific rifle and the height of your mounted optic, so check fit before taking it afield.
You'll need a torque wrench (set to 20 inch-pounds), a small brush or applicator for blue Loctite (sold separately), and possibly a small file to carefully trim the mount's corners and front edge for fitment on your particular rifle.
SKU: 194196361 • Weight: 0.2oz