RCBS167522143
Rcbs Matchmaster Competition Seating Die 6Mm Dasher$134.86
Availability: In Stock
The Redding Competition Rifle Seating Die for 6mm Dasher is purpose-built for precision handloaders who demand concentricity and consistency shot after shot. This isn't a generic seating die—Redding engineered it to solve the alignment problems that plague standard designs. If you're working up loads for 6mm Dasher competition or long-range hunting, you need a seating die that keeps bullets centered in the case and seated to exact depth, every single time.
The core innovation here is the seating stem system. Redding manufactures the stem to match your bullet diameter with precision-ground tolerances so tight that the stem actually floats on a column of air—eliminating the binding and runout that degraded older designs. Before seating even begins, the case and bullet are fully supported and aligned in a close-fitting precision ground sleeve, locking in concentricity from the start. This straightforward approach beats the geometric compromises built into competing seating dies.
Setup is straightforward: the micrometer adjusts in .001-inch increments and runs infinitely smooth without clicks, so you dial in your seating depth with repeatable precision. A setting feature lets you lock in your preferred depth once and return to it reliably, shot to shot. This is the die to reach for when your 6mm Dasher demands the same attention to detail you're already putting into brass prep and primer selection.
| Caliber | 6mm Dasher |
| Type | Competition Rifle Seating Die |
| Manufacturer | Redding |
| Micrometer Adjustment | .001-inch increments |
No. Redding does not recommend this die for use with compressed loads.
The seating stem is precision-ground to match bullet diameter exactly, and the bullet and case are fully supported in a close-fitting precision sleeve before seating begins. This design eliminates the concentricity problems built into standard seating dies. The stem tolerances are tight enough that the stem can float on a column of air, preventing binding and runout.
The micrometer adjusts infinitely in .001-inch increments and includes a setting feature that lets you lock in your preferred seating depth, so you can return to the same depth reliably with every load.
This is a rifle seating die, designed for 6mm Dasher rifle cartridges.
SKU: 167522111 • Width: 4.4in • Height: 1.75in • Depth: 5.9in • Weight: 0.89oz
Availability: In Stock
The Redding Competition Rifle Seating Die for 6mm Dasher is purpose-built for precision handloaders who demand concentricity and consistency shot after shot. This isn't a generic seating die—Redding engineered it to solve the alignment problems that plague standard designs. If you're working up loads for 6mm Dasher competition or long-range hunting, you need a seating die that keeps bullets centered in the case and seated to exact depth, every single time.
The core innovation here is the seating stem system. Redding manufactures the stem to match your bullet diameter with precision-ground tolerances so tight that the stem actually floats on a column of air—eliminating the binding and runout that degraded older designs. Before seating even begins, the case and bullet are fully supported and aligned in a close-fitting precision ground sleeve, locking in concentricity from the start. This straightforward approach beats the geometric compromises built into competing seating dies.
Setup is straightforward: the micrometer adjusts in .001-inch increments and runs infinitely smooth without clicks, so you dial in your seating depth with repeatable precision. A setting feature lets you lock in your preferred depth once and return to it reliably, shot to shot. This is the die to reach for when your 6mm Dasher demands the same attention to detail you're already putting into brass prep and primer selection.
| Caliber | 6mm Dasher |
| Type | Competition Rifle Seating Die |
| Manufacturer | Redding |
| Micrometer Adjustment | .001-inch increments |
No. Redding does not recommend this die for use with compressed loads.
The seating stem is precision-ground to match bullet diameter exactly, and the bullet and case are fully supported in a close-fitting precision sleeve before seating begins. This design eliminates the concentricity problems built into standard seating dies. The stem tolerances are tight enough that the stem can float on a column of air, preventing binding and runout.
The micrometer adjusts infinitely in .001-inch increments and includes a setting feature that lets you lock in your preferred seating depth, so you can return to the same depth reliably with every load.
This is a rifle seating die, designed for 6mm Dasher rifle cartridges.
SKU: 167522111 • Width: 4.4in • Height: 1.75in • Depth: 5.9in • Weight: 0.89oz