$14.51$18.95
Availability: In Stock
The Magpul MAG325-ODG MOE/CTR cheek riser is a quick-snap accessory that addresses one of the most common ergonomic challenges in tactical and hunting rifle setups: getting your face in the right spot behind your optic or sights. This polymer cheek riser mounts directly to Magpul CTR and MOE buttstocks without any permanent modification, giving you a solid, repeatable cheekweld that translates to faster target acquisition and more consistent accuracy downrange.
A proper cheekweld matters more than many shooters realize, especially when you're running magnified optics or trying to get clean repeatable hits at distance. By raising your eye naturally into the sight picture, you eliminate parallax issues, improve sight alignment, and reduce the time it takes to get on target. This particular model raises your cheekweld by 0.25 inches—a modest lift that works well for shooters transitioning between different stocks or fine-tuning their setup on a precision rifle. Since Magpul offers the cheek riser in three different heights, you can dial in exactly the rise you need for your particular optic and stock combination.
The OD Green finish matches standard Magpul furniture and is built from the same durable molded polymer used throughout their stock line. It snaps on and off without tools, so you can experiment with the fit or swap it between rifles. Keep in mind that on AR-15 platforms, the stock will need to remain in the fully extended position to maintain proper charging handle clearance. For non-AR installations—precision rifles, DMRs, or any build using a standalone CTR or MOE stock—there are no operational restrictions.
| Brand | Magpul |
| Model | MAG325-ODG |
| Cheekweld Raise | 0.25 inches |
| Finish | OD Green |
| Material | Molded polymer |
| Compatible Stocks | Magpul CTR, MOE |
| Installation | Snap-on, no tools required |
Yes, but with a caveat: your stock must remain in the fully extended position to allow unobstructed operation of the charging handle. If you plan to use a collapsed stock, this riser isn't the right fit for your setup.
Absolutely. The cheek riser is designed for any rifle using a Magpul CTR or MOE buttstock, and there are no operational restrictions on non-AR installations.
No. The cheek riser snaps on without any tools or permanent alterations to your stock. You can remove it or swap it between rifles as needed.
Magpul offers this cheek riser in three different heights: 0.25 inches, 0.5 inches, and 0.75 inches. You can choose the model that best matches your optic and facial geometry.
SKU: 115721314 • Width: 1.7in • Height: 1.5in • Depth: 6.5in • Weight: 0.11oz
Availability: In Stock
The Magpul MAG325-ODG MOE/CTR cheek riser is a quick-snap accessory that addresses one of the most common ergonomic challenges in tactical and hunting rifle setups: getting your face in the right spot behind your optic or sights. This polymer cheek riser mounts directly to Magpul CTR and MOE buttstocks without any permanent modification, giving you a solid, repeatable cheekweld that translates to faster target acquisition and more consistent accuracy downrange.
A proper cheekweld matters more than many shooters realize, especially when you're running magnified optics or trying to get clean repeatable hits at distance. By raising your eye naturally into the sight picture, you eliminate parallax issues, improve sight alignment, and reduce the time it takes to get on target. This particular model raises your cheekweld by 0.25 inches—a modest lift that works well for shooters transitioning between different stocks or fine-tuning their setup on a precision rifle. Since Magpul offers the cheek riser in three different heights, you can dial in exactly the rise you need for your particular optic and stock combination.
The OD Green finish matches standard Magpul furniture and is built from the same durable molded polymer used throughout their stock line. It snaps on and off without tools, so you can experiment with the fit or swap it between rifles. Keep in mind that on AR-15 platforms, the stock will need to remain in the fully extended position to maintain proper charging handle clearance. For non-AR installations—precision rifles, DMRs, or any build using a standalone CTR or MOE stock—there are no operational restrictions.
| Brand | Magpul |
| Model | MAG325-ODG |
| Cheekweld Raise | 0.25 inches |
| Finish | OD Green |
| Material | Molded polymer |
| Compatible Stocks | Magpul CTR, MOE |
| Installation | Snap-on, no tools required |
Yes, but with a caveat: your stock must remain in the fully extended position to allow unobstructed operation of the charging handle. If you plan to use a collapsed stock, this riser isn't the right fit for your setup.
Absolutely. The cheek riser is designed for any rifle using a Magpul CTR or MOE buttstock, and there are no operational restrictions on non-AR installations.
No. The cheek riser snaps on without any tools or permanent alterations to your stock. You can remove it or swap it between rifles as needed.
Magpul offers this cheek riser in three different heights: 0.25 inches, 0.5 inches, and 0.75 inches. You can choose the model that best matches your optic and facial geometry.
SKU: 115721314 • Width: 1.7in • Height: 1.5in • Depth: 6.5in • Weight: 0.11oz