L.E. Wilson194197026
L.E. Wilson 6.5X284Mm Winchester Bullet Seating Die$79.20
Availability: In Stock
Current Stock: Out of stock
The L.E. Wilson 270 Winchester bullet seating die is built for reloaders who demand precision. This chamber-type seating die is engineered to capture and align both the bullet and cartridge case before seating, producing the repeatable, low-runout results that serious handloaders—especially benchrest competitors—depend on. Unlike conventional 7/8-inch by 14 TPI seaters, Wilson's chamber-type design controls alignment from the moment the case enters the die, then seats the bullet straight down through a close-fitting stem. The result is accuracy that's hard to match.
If you're loading ammunition for precision rifle work—whether you're chasing tight groups at 100 yards or dialing in a hunting load—this die will tighten your standards. The seating depth is adjusted via cap screw with 3/8-inch by 24 TPI threading, giving you fine, repeatable control over bullet seating length. All stainless steel construction means this die will handle thousands of rounds without wear or corrosion.
L.E. Wilson has earned a reputation for accuracy-focused reloading equipment, and this seater die is made in the USA. If you're already investing the time to reload precision ammunition, you want tooling that won't be the weak link in your system.
| Caliber | 270 Winchester |
| Die Type | Chamber-type bullet seating die |
| Seating Adjustment | Cap screw, 3/8-inch–24 TPI |
| Material | Stainless steel |
| Included Items | Seater die, seater base, allen wrench, instructions |
| Origin | Made in the USA |
A chamber-type die captures and aligns both the case and bullet before the bullet is seated. This positive alignment produces lower runout and more consistent results than a conventional seater, where the case may shift slightly during the seating stroke. The design is more accurate and is favored by benchrest shooters and precision reloaders.
The die ships with the seater die itself, seater base, an allen wrench for adjustment, and printed instructions.
This die is designed for use in a standard reloading press, but you should verify compatibility with your specific press model. Contact us if you have questions about setup with your equipment.
Yes. Seating depth is adjusted by turning the cap screw (3/8-inch by 24 TPI) at the top of the die, allowing you to fine-tune bullet seating length for your load specifications and chamber.
SKU: 194196991 • Weight: 1oz
Availability: In Stock
Current Stock: Out of stock
The L.E. Wilson 270 Winchester bullet seating die is built for reloaders who demand precision. This chamber-type seating die is engineered to capture and align both the bullet and cartridge case before seating, producing the repeatable, low-runout results that serious handloaders—especially benchrest competitors—depend on. Unlike conventional 7/8-inch by 14 TPI seaters, Wilson's chamber-type design controls alignment from the moment the case enters the die, then seats the bullet straight down through a close-fitting stem. The result is accuracy that's hard to match.
If you're loading ammunition for precision rifle work—whether you're chasing tight groups at 100 yards or dialing in a hunting load—this die will tighten your standards. The seating depth is adjusted via cap screw with 3/8-inch by 24 TPI threading, giving you fine, repeatable control over bullet seating length. All stainless steel construction means this die will handle thousands of rounds without wear or corrosion.
L.E. Wilson has earned a reputation for accuracy-focused reloading equipment, and this seater die is made in the USA. If you're already investing the time to reload precision ammunition, you want tooling that won't be the weak link in your system.
| Caliber | 270 Winchester |
| Die Type | Chamber-type bullet seating die |
| Seating Adjustment | Cap screw, 3/8-inch–24 TPI |
| Material | Stainless steel |
| Included Items | Seater die, seater base, allen wrench, instructions |
| Origin | Made in the USA |
A chamber-type die captures and aligns both the case and bullet before the bullet is seated. This positive alignment produces lower runout and more consistent results than a conventional seater, where the case may shift slightly during the seating stroke. The design is more accurate and is favored by benchrest shooters and precision reloaders.
The die ships with the seater die itself, seater base, an allen wrench for adjustment, and printed instructions.
This die is designed for use in a standard reloading press, but you should verify compatibility with your specific press model. Contact us if you have questions about setup with your equipment.
Yes. Seating depth is adjusted by turning the cap screw (3/8-inch by 24 TPI) at the top of the die, allowing you to fine-tune bullet seating length for your load specifications and chamber.
SKU: 194196991 • Weight: 1oz