Hornady152746641
Horn 398309 Lock-N-Load Ap Case Feeder/Ez-Ject$103.81
Availability: In Stock
The Hornady Lock-N-Load Case Feeder is a motorized case-feeding attachment designed to boost throughput on your Lock-N-Load AP reloading press. If you're running high-volume handloading sessions and want to cut down on manual case handling, this feeder automates the job—capable of feeding cases at rates exceeding 500 rounds per hour, depending on your setup and technique. The unit runs on 110-volt power and pairs directly with Lock-N-Load AP presses (serial number 7000 and above; a conversion sub-plate is available for earlier models).
The feeder ships with six cartridge adaptors and uses a slotted cam wire mechanism that protects against jams if a case misfeed or shuttle adjustment goes wrong. Swapping calibers takes roughly five minutes: identify the right adaptor from the included V-Block chart, swap the case feeder plate (sold separately), and you're ready to run a different cartridge. So long as Hornady makes a standard shell plate for your round, the hopper will feed it.
This is a serious workhorse for reloaders who move real volume. The high-torque motor and large case bowl handle extended sessions without complaint. If you're tired of hand-priming or single-stage feeding, the Lock-N-Load Case Feeder cuts wasted motion and keeps your eyes on the press, not the hopper.
| Power | 110 Volt AC |
| Compatible Press | Hornady Lock-N-Load AP (serial 7000+) |
| Cartridge Adaptors Included | 6 |
| Throughput | 500+ rounds per hour (varies by experience and setup) |
| Case Feeder Plates | Sold separately |
Yes, if your press has a serial number 7000 or higher. Earlier models require a sub-plate conversion kit (available separately) to adapt the feeder.
Yes. The case feeder itself comes complete with six cartridge adaptors and all other necessary components, but the shell plates are sold separately based on the cartridges you reload.
Typical changeovers take about 5 minutes—you identify the correct adaptor from the included V-Block chart and swap components.
The Lock-N-Load Case Feeder works with any standard cartridge for which Hornady manufactures a shell plate. Check Hornady's product line to confirm availability for your specific round.
SKU: 152746638 • Width: 16.9in • Height: 12.3in • Depth: 20.3in • Weight: 17.425oz
Availability: In Stock
The Hornady Lock-N-Load Case Feeder is a motorized case-feeding attachment designed to boost throughput on your Lock-N-Load AP reloading press. If you're running high-volume handloading sessions and want to cut down on manual case handling, this feeder automates the job—capable of feeding cases at rates exceeding 500 rounds per hour, depending on your setup and technique. The unit runs on 110-volt power and pairs directly with Lock-N-Load AP presses (serial number 7000 and above; a conversion sub-plate is available for earlier models).
The feeder ships with six cartridge adaptors and uses a slotted cam wire mechanism that protects against jams if a case misfeed or shuttle adjustment goes wrong. Swapping calibers takes roughly five minutes: identify the right adaptor from the included V-Block chart, swap the case feeder plate (sold separately), and you're ready to run a different cartridge. So long as Hornady makes a standard shell plate for your round, the hopper will feed it.
This is a serious workhorse for reloaders who move real volume. The high-torque motor and large case bowl handle extended sessions without complaint. If you're tired of hand-priming or single-stage feeding, the Lock-N-Load Case Feeder cuts wasted motion and keeps your eyes on the press, not the hopper.
| Power | 110 Volt AC |
| Compatible Press | Hornady Lock-N-Load AP (serial 7000+) |
| Cartridge Adaptors Included | 6 |
| Throughput | 500+ rounds per hour (varies by experience and setup) |
| Case Feeder Plates | Sold separately |
Yes, if your press has a serial number 7000 or higher. Earlier models require a sub-plate conversion kit (available separately) to adapt the feeder.
Yes. The case feeder itself comes complete with six cartridge adaptors and all other necessary components, but the shell plates are sold separately based on the cartridges you reload.
Typical changeovers take about 5 minutes—you identify the correct adaptor from the included V-Block chart and swap components.
The Lock-N-Load Case Feeder works with any standard cartridge for which Hornady manufactures a shell plate. Check Hornady's product line to confirm availability for your specific round.
SKU: 152746638 • Width: 16.9in • Height: 12.3in • Depth: 20.3in • Weight: 17.425oz