Forster197558796
Forster Products 0.323'' Hand Held Neck Turner Pilot$16.68
Loading...
Loading...
Loading...
Availability: In Stock
Current Stock: Out of stock
The Forster Hand Held Outside Neck Turner is a manual case preparation tool designed for reloaders who want to dial in cartridge-to-cartridge consistency. If you're serious about handload precision—especially for long-range or competition ammunition—this device addresses a real bottleneck: neck wall thickness variation. Uneven case necks cause bullets to sit at inconsistent angles relative to bore centerline, which kills accuracy. This tool uses a carbide cutter to trim the outside of fired case necks down to uniform dimensions, giving you the kind of case prep control that separates bench rest-grade ammo from the rest.
Setup is straightforward. The aluminum holder clamps the case firmly with a simple knob turn and accommodates cases with a base diameter up to .592 inches. The micrometer-style adjustment knob lets you dial in exactly how much material to remove—precision work without guesswork. The carbide cutter handles the heavy lifting; carbide won't dull quickly like steel, so you'll stay consistent across dozens of cases. Each turn of the handle removes a controlled amount of brass from the case neck's exterior, bringing wall thickness into spec.
One critical point: this tool requires a pilot that matches your specific case mouth diameter—pilots are sold separately and are precision-ground to sit .002" to .0025" smaller than bullet diameter. That's tight tolerances by design, ensuring the cutter stays true. Before you buy, verify the pilot size you need for your cartridge and order it along with the turner itself.
Neck turning isn't mandatory for casual hunting loads, but it's a game-changer if you're loading match ammunition, pushing long-range shots, or chasing sub-minute-of-angle groups. The Forster hand-held design gives you full control and doesn't require powered equipment—just your hands and attention to detail.
| Cutter Type | Carbide |
| Adjustment Style | Micrometer-style knob |
| Maximum Case Base Diameter | .592 inches |
| Pilot Clearance | .002" to .0025" smaller than bullet diameter |
| Operation | Hand-held, manual |
Pilots are specific to case mouth diameter and are sold separately. Forster manufactures pilots for common cartridges; measure your case mouth diameter and order the pilot that matches your load. Pilots are precision-ground .002" to .0025" smaller than bullet diameter to ensure accurate neck turning.
The tool handles cases with a base diameter up to .592 inches. That covers most rifle cartridges, but if you're loading magnum or belted cases, verify your case base diameter against this limit before purchasing.
No. The Forster Hand Held Outside Neck Turner is entirely manual—you clamp the case, set the micrometer adjustment, and turn the tool by hand. No electricity or additional equipment required.
SKU: 167523432 • Width: 4.15in • Height: 1.65in • Depth: 7.1in • Weight: 0.55oz
Availability: In Stock
Current Stock: Out of stock
The Forster Hand Held Outside Neck Turner is a manual case preparation tool designed for reloaders who want to dial in cartridge-to-cartridge consistency. If you're serious about handload precision—especially for long-range or competition ammunition—this device addresses a real bottleneck: neck wall thickness variation. Uneven case necks cause bullets to sit at inconsistent angles relative to bore centerline, which kills accuracy. This tool uses a carbide cutter to trim the outside of fired case necks down to uniform dimensions, giving you the kind of case prep control that separates bench rest-grade ammo from the rest.
Setup is straightforward. The aluminum holder clamps the case firmly with a simple knob turn and accommodates cases with a base diameter up to .592 inches. The micrometer-style adjustment knob lets you dial in exactly how much material to remove—precision work without guesswork. The carbide cutter handles the heavy lifting; carbide won't dull quickly like steel, so you'll stay consistent across dozens of cases. Each turn of the handle removes a controlled amount of brass from the case neck's exterior, bringing wall thickness into spec.
One critical point: this tool requires a pilot that matches your specific case mouth diameter—pilots are sold separately and are precision-ground to sit .002" to .0025" smaller than bullet diameter. That's tight tolerances by design, ensuring the cutter stays true. Before you buy, verify the pilot size you need for your cartridge and order it along with the turner itself.
Neck turning isn't mandatory for casual hunting loads, but it's a game-changer if you're loading match ammunition, pushing long-range shots, or chasing sub-minute-of-angle groups. The Forster hand-held design gives you full control and doesn't require powered equipment—just your hands and attention to detail.
| Cutter Type | Carbide |
| Adjustment Style | Micrometer-style knob |
| Maximum Case Base Diameter | .592 inches |
| Pilot Clearance | .002" to .0025" smaller than bullet diameter |
| Operation | Hand-held, manual |
Pilots are specific to case mouth diameter and are sold separately. Forster manufactures pilots for common cartridges; measure your case mouth diameter and order the pilot that matches your load. Pilots are precision-ground .002" to .0025" smaller than bullet diameter to ensure accurate neck turning.
The tool handles cases with a base diameter up to .592 inches. That covers most rifle cartridges, but if you're loading magnum or belted cases, verify your case base diameter against this limit before purchasing.
No. The Forster Hand Held Outside Neck Turner is entirely manual—you clamp the case, set the micrometer adjustment, and turn the tool by hand. No electricity or additional equipment required.
SKU: 167523432 • Width: 4.15in • Height: 1.65in • Depth: 7.1in • Weight: 0.55oz